Rice-lake Counterpart Configurable Counting Indicator - Inst User Manual Page 78
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
72 Counterpart Counting Scale Indicator
6.0 Serial Commands
The Counterpart can be controlled by a PC or remote keyboard connected to an indicator serial port. Control is
provided by a set of serial commands that can simulate front panel key press functions, display and change setup
parameters, and perform reporting functions. This provides the ability to print configuration data or to save to your
hard drive.
6.1 The Serial Command Set
The serial command set can be divided into five groups: key press commands, reporting commands, the
RESETCONFIGURATION special function command, parameter setting commands, and transmit weight data
commands. When a serial command is processed, the Counterpart responds with the message
OK. The OK response
verifies that the command was received and has been executed. If the command is unrecognized or cannot be
executed, the Counterpart responds with
??.
The following sections list the commands and command syntax used for each of these groups.
6.1.1 Key Press Commands
Key press serial commands simulate pressing the keys on the front panel of the indicator. These commands can be
used in both setup and normal (weighing) mode. Several of the commands serve as “pseudo” keys, providing
functions that are not represented by a key on the front panel.
For example, to enter a 15 lb tare weight:
1. Type K1 and press ENTER (or RETURN).
2. Type K5 and press ENTER.
3. Type KTARE and press ENTER.
Command Function
KMENU Press the MENU key.
KZERO In weighing mode, press the ZERO key.
KUNITS In weighing mode, press the UNITS key.
KPRINT In weighing mode, press the PRINT key.
KTARE Press the TARE key.
KID In weighing mode, press the ID key. In menu mode, move left in the menu. In data entry mode, move to
previous digit.
KGROSSNET In weighing mode, press the GROSS/NET key (pseudo key).
KGROSS Go to gross mode (pseudo key).
KNET Go to net mode (pseudo key).
KDISPACCUM Display ACCUM (pseudo key).
KDISPTARE Display tare (pseudo key).
KCLR Press the CLEAR key.
KCLRCN Reset consecutive number (pseudo key).
KCLRTAR Clear tare from system (pseudo key).
KLEFT In menu mode, move left in the menu.
KRIGHT In menu mode, move right in the menu.
KUP In weighing mode, press the UNDER key. In menu mode, move down in the menu. In data entry mode,
decrement the current digit.
KDOWN In weighing mode, press the UNDER key. In menu mode, move down in the menu. In data entry mode,
decrement the current digit.
KSAVE In menu mode, saves the current configuration.
KEXIT In menu mode, saves the current configuration then exits to normal mode.
K0–K9 Press number 0 (zero) through 9.
KDOT Press the decimal point (.)
Table 6-1. Serial Key Press Commands
- Counterpart 1
- User Manual 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 8
- 1.4 Keypad Functions 9
- 1.5 Tare Recall 10
- 1.6 Annunciator Symbols 10
- 1.7 Softkey Setup 11
- 1.9 Indicator Operations 11
- 2.0 Installation 13
- Important 13
- 2.3 Enclosure Disassembly 15
- 2.5 Making Power Connections 16
- 2.6 Load Cell Wiring 16
- 2.7 Wire Specifics 17
- 2.8 Cable Grounding 18
- 2.9 Enclosure Reassembly 19
- 2.10 CPU Board Removal 19
- 2.13 Installing Option Cards 21
- Figure 2-14. CPU Board 22
- Counterpart Front View 25
- Counterpart Dimensions 27
- 3.0 Configuration 28
- 3.3 Revolution Configuration 29
- 3.4 ID Menu 30
- 3.5 Audit Menu 31
- 3.6 Calibration Menu 32
- 3.7 Setup Menu 33
- 3.7.1 Scale Menu 34
- Scale Calibration Menu 37
- Scale Format Menu 38
- Scale Format Menu Parameters 39
- 3.7.2 Feature Menu 40
- UNITWTUPDATE 41
- Feature Count Menu 42
- Feature Region Menu 44
- SOFTKEYS Menu 45
- Regulate Industry Menu 46
- 3.7.3 Serial Menu 48
- 3.7.4 Ethernet Menu 50
- 3.7.5 Print Format Menu 51
- 3.7.6 Scale Setpoints Menu 52
- LIST OF 53
- 3.7.7 DIG I/O Menu 56
- 3.8 Test Menu 57
- 3.9 Display Menu 58
- SETPT 2 - 6 59
- 4.0 Calibration 61
- 4.2 Five-point Linearization 62
- 4.3 Rezero 62
- 4.4 EDP Command Calibration 62
- 4.5 Revolution 63
- Calibration 63
- 4.6 More About Calibration 64
- 5.0 Scale Operations 65
- 0.000653642 - 0.000653 x 100 66
- 0.000653642 66
- = 0.098% 66
- Figure 5-1. ID Menu 68
- 5.5.2 Using a Stored ID 69
- 5.5.4 Clearing ID Codes 70
- 5.6 WeighVault 71
- 5.6.2 Using WeighVault 72
- 5.7 Totalization Counts 73
- 5.8 Parts Reduction Counts 74
- 5.10 Batch Operations 75
- DIGITAL I/O 76
- 5.12 USB Keyboard 77
- 6.0 Serial Commands 78
- 6.1.2 ID Commands 79
- 6.1.3 Reporting Commands 79
- 6.1.6 Normal Mode Commands 84
- 6.1.7 Unique Commands 84
- 7.0 Print Formatting 85
- Table 7-3. H1, H2 Formats 88
- 7.2 Customizing Print Formats 89
- 7.2.3 Using Revolution 90
- 7.2.4 Print Label Examples 90
- Count Format 91
- Pallet Label Format 91
- Gross Label Format 91
- Setpoint Format 92
- Total Label Format 92
- Gross/Tare/Net Label Format 93
- Accum Label Format 93
- 8.1 Enclosure Disassembly 94
- 8.2 WLAN Card Installation 94
- - - - - - 95
- 9.2.1 Using the P EDP Command 96
- <LF> 97
- 9.6 Digital Filtering 100
- 9.6.4 Audit Trail Support 101
- 9.7 USB Keyboard Interface 102
- 9.8 Serial Scale Interface 102
- 9.9 Regulatory Mode Functions 103
- 9.11 Updating Firmware 105
- Figure 9-4. Revolution Screen 106
- 9.12 Specifications 107
- 9.13 Specifications 108
- Counterpart Limited Warranty 109
- For More Information 110
Related products and manuals for Scales Rice-lake Counterpart Configurable Counting Indicator - Inst
Scales Rice-lake CW-90X Base User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 2.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals