Rice-lake Counterpart Configurable Counting Indicator - Inst User Manual Page 63
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Calibration 57
5. Up to five linearization points can be calibrated between the zero and span calibration values. Use the
following commands to set and calibrate a single linearization point:
SC.WLIN.V1=nnnnn<CR>
SC.WLIN.C1<CR>
The SC.WLIN.V1#n command sets the test weight value (nnnnn) for linearization point 1. The
SC.WLIN.C1#n command calibrates the point. Repeat using the SC.WLIN.Vx and SC.WLIN.Cx
commands as required for additional linearization points.
6. To remove an offset value, clear all weight from the scale, including hooks or chains used to hang test
weights, and send the SC.REZERO#n command. The indicator displays
CALIBRATING while the zero and
span calibrations are adjusted.
7. Send the SC.KUPARROW#n or the SC.KEXIT#n EDP command to return to normal mode.
4.5 Revolution
®
Calibration
To calibrate the indicator using Revolution, the indicator EDP port must be connected to a PC running the
Revolution configuration utility.
1. Place the indicator in config mode (display reads SCALE, — see Figure 3-8 on page 28) and remove all
weight from the scale platform.
2. From Revolution, select File » New. The Select Indicator dialog box appears.
3. Select Counterpart and click OK.
4. From the Communications menu, select Connect.
5. From the left pane, expand the Scale selection and click the Scale button.
Figure 4-2. Scale Button
6. From the Tools menu, select Calibration Wizard.
7. Click NEXT to begin the Calibration Wizard.
8. Select whether you want to perform a standard calibration or a standard with multi-point linearization and
click
NEXT.
9. In the text box, enter the test weight value to be used for span calibration.
10. Select the check box if you are using chains or hooks during the calibration, and click NEXT.
11. Remove all weight from the scale and click Click to Calibrate Zero to begin zero calibration. If your test
weights require hooks or chains, place them on the scale for zero calibration.
12. When zero calibration is complete, the Calibration Wizard prompts you to place test weights on the scale.
Place the test weights on the scale and click
Click to Calibrate Span.
13. If you chose to perform linear calibration, the Calibration Wizard now displays prompts (1–5). Enter the
weight value for Linear Point #1, place test weights on scale, and click
GO. Repeat for additional
linearization points and click
NEXT.
14. The new and old calibration settings are displayed. To accept the new values, click Finish. To exit and
restore the old values, click
Cancel.
- Counterpart 1
- User Manual 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 8
- 1.4 Keypad Functions 9
- 1.5 Tare Recall 10
- 1.6 Annunciator Symbols 10
- 1.7 Softkey Setup 11
- 1.9 Indicator Operations 11
- 2.0 Installation 13
- Important 13
- 2.3 Enclosure Disassembly 15
- 2.5 Making Power Connections 16
- 2.6 Load Cell Wiring 16
- 2.7 Wire Specifics 17
- 2.8 Cable Grounding 18
- 2.9 Enclosure Reassembly 19
- 2.10 CPU Board Removal 19
- 2.13 Installing Option Cards 21
- Figure 2-14. CPU Board 22
- Counterpart Front View 25
- Counterpart Dimensions 27
- 3.0 Configuration 28
- 3.3 Revolution Configuration 29
- 3.4 ID Menu 30
- 3.5 Audit Menu 31
- 3.6 Calibration Menu 32
- 3.7 Setup Menu 33
- 3.7.1 Scale Menu 34
- Scale Calibration Menu 37
- Scale Format Menu 38
- Scale Format Menu Parameters 39
- 3.7.2 Feature Menu 40
- UNITWTUPDATE 41
- Feature Count Menu 42
- Feature Region Menu 44
- SOFTKEYS Menu 45
- Regulate Industry Menu 46
- 3.7.3 Serial Menu 48
- 3.7.4 Ethernet Menu 50
- 3.7.5 Print Format Menu 51
- 3.7.6 Scale Setpoints Menu 52
- LIST OF 53
- 3.7.7 DIG I/O Menu 56
- 3.8 Test Menu 57
- 3.9 Display Menu 58
- SETPT 2 - 6 59
- 4.0 Calibration 61
- 4.2 Five-point Linearization 62
- 4.3 Rezero 62
- 4.4 EDP Command Calibration 62
- 4.5 Revolution 63
- Calibration 63
- 4.6 More About Calibration 64
- 5.0 Scale Operations 65
- 0.000653642 - 0.000653 x 100 66
- 0.000653642 66
- = 0.098% 66
- Figure 5-1. ID Menu 68
- 5.5.2 Using a Stored ID 69
- 5.5.4 Clearing ID Codes 70
- 5.6 WeighVault 71
- 5.6.2 Using WeighVault 72
- 5.7 Totalization Counts 73
- 5.8 Parts Reduction Counts 74
- 5.10 Batch Operations 75
- DIGITAL I/O 76
- 5.12 USB Keyboard 77
- 6.0 Serial Commands 78
- 6.1.2 ID Commands 79
- 6.1.3 Reporting Commands 79
- 6.1.6 Normal Mode Commands 84
- 6.1.7 Unique Commands 84
- 7.0 Print Formatting 85
- Table 7-3. H1, H2 Formats 88
- 7.2 Customizing Print Formats 89
- 7.2.3 Using Revolution 90
- 7.2.4 Print Label Examples 90
- Count Format 91
- Pallet Label Format 91
- Gross Label Format 91
- Setpoint Format 92
- Total Label Format 92
- Gross/Tare/Net Label Format 93
- Accum Label Format 93
- 8.1 Enclosure Disassembly 94
- 8.2 WLAN Card Installation 94
- - - - - - 95
- 9.2.1 Using the P EDP Command 96
- <LF> 97
- 9.6 Digital Filtering 100
- 9.6.4 Audit Trail Support 101
- 9.7 USB Keyboard Interface 102
- 9.8 Serial Scale Interface 102
- 9.9 Regulatory Mode Functions 103
- 9.11 Updating Firmware 105
- Figure 9-4. Revolution Screen 106
- 9.12 Specifications 107
- 9.13 Specifications 108
- Counterpart Limited Warranty 109
- For More Information 110
Related products and manuals for Scales Rice-lake Counterpart Configurable Counting Indicator - Inst
Scales Rice-lake CW-90X Base User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 2.161 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals