Rice-lake Counterpart Configurable Counting Indicator - Inst User Manual Page 61
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Calibration 55
4.0 Calibration
The Counterpart can be calibrated using the front panel, EDP commands, or Revolution
®
.
Calibration can be performed in two places within the menu: the CALIBR menu shown in Figure 4-1 and the
SCALE sub-menu shown in Figure 3-8 on page 28. The CALIBR menu shown in Figure 4-1 is a “quick access”
calibration; for more in-depth scale setup and calibration, use the menus found under SETUP/CONFIG/
SCALE (see Figure 3-8 on page 28).
Calibration consists of the following steps:
• Zero calibration
• Entering the test weight value
• Span calibration
• Optional five-point linearization
• Optional rezero calibration for test weights using hooks or chains.
The Counterpart requires the WZERO and WSPAN points to be calibrated. The linearity points are optional,
but must not duplicate zero or span. During calibration, the TARE (Enter) key acts as a data entry confirmation
key. The soft calibrate key accepts that value.
Figure 4-1. Calibration (CALIBR) Menu
4.1 Front Panel Calibration
1. Press the MENU SETUP button, and then press until the display reads CALIBR.
2. Press TARE (E nter) or to go to the scale to be calibrated. Press TA RE (En ter) or to go to WZERO. Press
TARE (En ter) again to display a value and press the Calibrate softkey to Calibrate WZERO.
If you do not want to calibrate zero, press Menu to exit.
3. The indicator displays CALIBRATING while calibration is in progress. When complete, press TARE (Enter) or
to advanced to the next prompt (WVAL).
To view the new AD count, repeat Step 3, but instead of pressing TARE (Enter) while viewing the value, press
MENU SETUP to exit.
4. With WVAL displayed, press TARE (Enter) or to display or edit the stored calibration weight value. Press
TARE (En ter) to store the WVAL value and advance to WSPAN.
5. With WSPAN displayed, press TARE (Ent er) or to view the A/D count. Place test weights on the scale equal
to WVAL. Press the Calibrate softkey to calibrate WSPAN.
Note
Note
Display and edit
test weight value
Same as POINT 1
Previous A/D raw
counts are shown
Press calibrate
softkey to calibrate
zero. Press menu
to cancel
calibrating.
Previous A/D raw
counts are shown
Press calibrate
softkey to calibrate
zero. Press menu
to cancel
calibrating.
Calibrating, please wait
Press enter to
remove offset from
zero and span
calibrations
POINT 1
POINT 2 POINT 3
POINT 4
POINT 5
WZERO WVAL WSPAN REZEROWLIN
WGT 1
CAL1
ID DISPLAYTESTSETUPAUDIT CALIBR SETPTS
Note
Note
- Counterpart 1
- User Manual 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 8
- 1.4 Keypad Functions 9
- 1.5 Tare Recall 10
- 1.6 Annunciator Symbols 10
- 1.7 Softkey Setup 11
- 1.9 Indicator Operations 11
- 2.0 Installation 13
- Important 13
- 2.3 Enclosure Disassembly 15
- 2.5 Making Power Connections 16
- 2.6 Load Cell Wiring 16
- 2.7 Wire Specifics 17
- 2.8 Cable Grounding 18
- 2.9 Enclosure Reassembly 19
- 2.10 CPU Board Removal 19
- 2.13 Installing Option Cards 21
- Figure 2-14. CPU Board 22
- Counterpart Front View 25
- Counterpart Dimensions 27
- 3.0 Configuration 28
- 3.3 Revolution Configuration 29
- 3.4 ID Menu 30
- 3.5 Audit Menu 31
- 3.6 Calibration Menu 32
- 3.7 Setup Menu 33
- 3.7.1 Scale Menu 34
- Scale Calibration Menu 37
- Scale Format Menu 38
- Scale Format Menu Parameters 39
- 3.7.2 Feature Menu 40
- UNITWTUPDATE 41
- Feature Count Menu 42
- Feature Region Menu 44
- SOFTKEYS Menu 45
- Regulate Industry Menu 46
- 3.7.3 Serial Menu 48
- 3.7.4 Ethernet Menu 50
- 3.7.5 Print Format Menu 51
- 3.7.6 Scale Setpoints Menu 52
- LIST OF 53
- 3.7.7 DIG I/O Menu 56
- 3.8 Test Menu 57
- 3.9 Display Menu 58
- SETPT 2 - 6 59
- 4.0 Calibration 61
- 4.2 Five-point Linearization 62
- 4.3 Rezero 62
- 4.4 EDP Command Calibration 62
- 4.5 Revolution 63
- Calibration 63
- 4.6 More About Calibration 64
- 5.0 Scale Operations 65
- 0.000653642 - 0.000653 x 100 66
- 0.000653642 66
- = 0.098% 66
- Figure 5-1. ID Menu 68
- 5.5.2 Using a Stored ID 69
- 5.5.4 Clearing ID Codes 70
- 5.6 WeighVault 71
- 5.6.2 Using WeighVault 72
- 5.7 Totalization Counts 73
- 5.8 Parts Reduction Counts 74
- 5.10 Batch Operations 75
- DIGITAL I/O 76
- 5.12 USB Keyboard 77
- 6.0 Serial Commands 78
- 6.1.2 ID Commands 79
- 6.1.3 Reporting Commands 79
- 6.1.6 Normal Mode Commands 84
- 6.1.7 Unique Commands 84
- 7.0 Print Formatting 85
- Table 7-3. H1, H2 Formats 88
- 7.2 Customizing Print Formats 89
- 7.2.3 Using Revolution 90
- 7.2.4 Print Label Examples 90
- Count Format 91
- Pallet Label Format 91
- Gross Label Format 91
- Setpoint Format 92
- Total Label Format 92
- Gross/Tare/Net Label Format 93
- Accum Label Format 93
- 8.1 Enclosure Disassembly 94
- 8.2 WLAN Card Installation 94
- - - - - - 95
- 9.2.1 Using the P EDP Command 96
- <LF> 97
- 9.6 Digital Filtering 100
- 9.6.4 Audit Trail Support 101
- 9.7 USB Keyboard Interface 102
- 9.8 Serial Scale Interface 102
- 9.9 Regulatory Mode Functions 103
- 9.11 Updating Firmware 105
- Figure 9-4. Revolution Screen 106
- 9.12 Specifications 107
- 9.13 Specifications 108
- Counterpart Limited Warranty 109
- For More Information 110
Related products and manuals for Scales Rice-lake Counterpart Configurable Counting Indicator - Inst
Scales Rice-lake CW-90X Base User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 1.792 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals