Rice-lake Counterpart Configurable Counting Indicator - Inst User Manual Page 69
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Scale Operations 63
5.5.1 Setting an ID Using the Normal Mode
1. Press the MENU SETUP key to access this menu.
2. Press to ID and then press and you will be at REG1.
3. Navigate to the REG number you want to set (1-150) by using the and keys.
All menus have wrap-around functionality. If you are at ID1 and want to access ID150, you can quickly do so by
moving backwards through the menu.
4. When you have reached the REG number you want to set, press to select that register number.
5. Press and enter the CODE value — either the numeric or alphanumeric is acceptable. Thirty two
characters can be entered and only 25 characters maximum for default bar code formats. This code will be
used to recall the ID.
6. When the desired value is entered, press TARE ( Enter).
7. Enter the information for description, part number, lot number, unit weight, tare with all entries being
optional.
8. Press TARE (Ente r) again to accept the value(s).
9. Press to advance back up to REG. Press again, and the DONE softkey is displayed.
10. When complete, push the DONE softkey.
Enter Lot Number — Optional
1. LOT will be displayed. Press key to enter the alphanumeric value using the Counterpart keypad.
2. Press the TARE (Enter) key to accept.
Enter Unit Weight — Optional
1. UNIT WT will be displayed. Press and enter the unit weight value using the Counterpart keypad.
2. Press the TARE (Enter) key to accept.
Enter Tare — Optional
1. TARE will be displayed. Press and enter the tare value using the Counterpart keypad.
2. Press the TARE (Enter) key to accept.
Enter Units — Optional
1. UNITS will be displayed. To adjust the units, use the and keys to adjust the selection or press to view
the current setting.
2. Use the key or the TARE (Enter) key to store the setting.
Enter Location — Optional
1. LOCATION is displayed. Use the key and enter a value. Push the TARE (E nt er) key to store.
5.5.2 Using a Stored ID
1. Press the CODE (softkey needs to be set up) key.
2. Counterpart responds with a code #=> with a prompt. Enter the ID code.
3. Press TARE (Ente r).
Press code and then enter a zero to unload an ID code.
5.5.3 Using ID/Codes that are not Stored
1. Enable Single ID under feature menu.
2. Setup softkeys for code and other information to be printed, including part #, description, and/or quantity.
3. Press Softkey.
4. Key in value or information and press Tare ( Ent er) .
5. The unit weight softkey may be set up to clear unit weight.
6. Next ID/code overrides data.
MENU
SETUP
Note
Note
- Counterpart 1
- User Manual 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 8
- 1.4 Keypad Functions 9
- 1.5 Tare Recall 10
- 1.6 Annunciator Symbols 10
- 1.7 Softkey Setup 11
- 1.9 Indicator Operations 11
- 2.0 Installation 13
- Important 13
- 2.3 Enclosure Disassembly 15
- 2.5 Making Power Connections 16
- 2.6 Load Cell Wiring 16
- 2.7 Wire Specifics 17
- 2.8 Cable Grounding 18
- 2.9 Enclosure Reassembly 19
- 2.10 CPU Board Removal 19
- 2.13 Installing Option Cards 21
- Figure 2-14. CPU Board 22
- Counterpart Front View 25
- Counterpart Dimensions 27
- 3.0 Configuration 28
- 3.3 Revolution Configuration 29
- 3.4 ID Menu 30
- 3.5 Audit Menu 31
- 3.6 Calibration Menu 32
- 3.7 Setup Menu 33
- 3.7.1 Scale Menu 34
- Scale Calibration Menu 37
- Scale Format Menu 38
- Scale Format Menu Parameters 39
- 3.7.2 Feature Menu 40
- UNITWTUPDATE 41
- Feature Count Menu 42
- Feature Region Menu 44
- SOFTKEYS Menu 45
- Regulate Industry Menu 46
- 3.7.3 Serial Menu 48
- 3.7.4 Ethernet Menu 50
- 3.7.5 Print Format Menu 51
- 3.7.6 Scale Setpoints Menu 52
- LIST OF 53
- 3.7.7 DIG I/O Menu 56
- 3.8 Test Menu 57
- 3.9 Display Menu 58
- SETPT 2 - 6 59
- 4.0 Calibration 61
- 4.2 Five-point Linearization 62
- 4.3 Rezero 62
- 4.4 EDP Command Calibration 62
- 4.5 Revolution 63
- Calibration 63
- 4.6 More About Calibration 64
- 5.0 Scale Operations 65
- 0.000653642 - 0.000653 x 100 66
- 0.000653642 66
- = 0.098% 66
- Figure 5-1. ID Menu 68
- 5.5.2 Using a Stored ID 69
- 5.5.4 Clearing ID Codes 70
- 5.6 WeighVault 71
- 5.6.2 Using WeighVault 72
- 5.7 Totalization Counts 73
- 5.8 Parts Reduction Counts 74
- 5.10 Batch Operations 75
- DIGITAL I/O 76
- 5.12 USB Keyboard 77
- 6.0 Serial Commands 78
- 6.1.2 ID Commands 79
- 6.1.3 Reporting Commands 79
- 6.1.6 Normal Mode Commands 84
- 6.1.7 Unique Commands 84
- 7.0 Print Formatting 85
- Table 7-3. H1, H2 Formats 88
- 7.2 Customizing Print Formats 89
- 7.2.3 Using Revolution 90
- 7.2.4 Print Label Examples 90
- Count Format 91
- Pallet Label Format 91
- Gross Label Format 91
- Setpoint Format 92
- Total Label Format 92
- Gross/Tare/Net Label Format 93
- Accum Label Format 93
- 8.1 Enclosure Disassembly 94
- 8.2 WLAN Card Installation 94
- - - - - - 95
- 9.2.1 Using the P EDP Command 96
- <LF> 97
- 9.6 Digital Filtering 100
- 9.6.4 Audit Trail Support 101
- 9.7 USB Keyboard Interface 102
- 9.8 Serial Scale Interface 102
- 9.9 Regulatory Mode Functions 103
- 9.11 Updating Firmware 105
- Figure 9-4. Revolution Screen 106
- 9.12 Specifications 107
- 9.13 Specifications 108
- Counterpart Limited Warranty 109
- For More Information 110
Related products and manuals for Scales Rice-lake Counterpart Configurable Counting Indicator - Inst
Scales Rice-lake CW-90X Base User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.552 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals