Rice-lake Counterpart Configurable Counting Indicator - Inst User Manual Page 58
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
52 Counterpart Counting Scale Indicator
3.9 Display Menu
There are three display settings on the Counterpart.
Figure 3-24. DISPLAY Menu
Setting the display parameters from this top level menu is temporary. After a power cycle, the values will revert to
their previous values. Changes made to these parameters through the CONFIG menu are kept through a power
cycle.
DIG I/O LOOP
DIO 1
DIO 2
DIO 3
DIO 4
Tests your digital I/O ports. If they are functioning, PASS is displayed. If they are not functioning,
FAIL is displayed.
Both inputs and outputs are active low. They go to a ground state when active.
The I/O ports become activated when the test is performed. Make sure
any equipment is disconnected prior to performing this test to avoid
inadvertently activating it.
COMM PORT1
PORT2
Performs a loop-back test on the serial ports. If they are functioning, PASS is displayed. If they are
not functioning, FAIL is displayed.
RAM TEST Tests the unit’s memory. If it is functioning, PASS is displayed. If it is not functioning, FAIL is
displayed.
KEYPAD TEST Tests the unit’s individual keypad buttons by displaying the name of the key pressed. If nothing is
displayed, the key is not functioning.
Press the Menu key to exit the test.
SCANNER TEST Displays scanned value with control characters.
A/D sub-menus
RAW VAL Displays the live current raw AD count.
ZERO VAL Displays the captured AD Zero calibration value.
SPAN VAL Displays the captured AD Span calibration value.
mV VAL Displays the live current millivolt signal voltage.
EXCVDC VAL Displays the current excitation voltage.
LOOP TEST Performs a loop test on dig I/O cards.
DIO 1
DIO 2
DIO 3
DIO 4
STATUS Displays the status of each individual digital I/O port. If set as input, the display shows input stats IN
HI or IN LO. If set as output, pressing
Enter toggles the output between HI and LO. OUT HI or OUT
LO.
OUT LO is active.
PORT1
PORT2
TEST Performs a loopback test on serial port 1 or 2. Connect jumper TX and RX together on port 1 or
port 2 before testing.
Parameter Choices Description
Table 3-19.
Note
WARNING
0-100%
50
Negative
Positive
ID DISPLAYTESTSETUPAUDIT CALIBR SETPTS
CONTRAST BRIGHT IMAGE
100
0-100%
- Counterpart 1
- User Manual 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 8
- 1.4 Keypad Functions 9
- 1.5 Tare Recall 10
- 1.6 Annunciator Symbols 10
- 1.7 Softkey Setup 11
- 1.9 Indicator Operations 11
- 2.0 Installation 13
- Important 13
- 2.3 Enclosure Disassembly 15
- 2.5 Making Power Connections 16
- 2.6 Load Cell Wiring 16
- 2.7 Wire Specifics 17
- 2.8 Cable Grounding 18
- 2.9 Enclosure Reassembly 19
- 2.10 CPU Board Removal 19
- 2.13 Installing Option Cards 21
- Figure 2-14. CPU Board 22
- Counterpart Front View 25
- Counterpart Dimensions 27
- 3.0 Configuration 28
- 3.3 Revolution Configuration 29
- 3.4 ID Menu 30
- 3.5 Audit Menu 31
- 3.6 Calibration Menu 32
- 3.7 Setup Menu 33
- 3.7.1 Scale Menu 34
- Scale Calibration Menu 37
- Scale Format Menu 38
- Scale Format Menu Parameters 39
- 3.7.2 Feature Menu 40
- UNITWTUPDATE 41
- Feature Count Menu 42
- Feature Region Menu 44
- SOFTKEYS Menu 45
- Regulate Industry Menu 46
- 3.7.3 Serial Menu 48
- 3.7.4 Ethernet Menu 50
- 3.7.5 Print Format Menu 51
- 3.7.6 Scale Setpoints Menu 52
- LIST OF 53
- 3.7.7 DIG I/O Menu 56
- 3.8 Test Menu 57
- 3.9 Display Menu 58
- SETPT 2 - 6 59
- 4.0 Calibration 61
- 4.2 Five-point Linearization 62
- 4.3 Rezero 62
- 4.4 EDP Command Calibration 62
- 4.5 Revolution 63
- Calibration 63
- 4.6 More About Calibration 64
- 5.0 Scale Operations 65
- 0.000653642 - 0.000653 x 100 66
- 0.000653642 66
- = 0.098% 66
- Figure 5-1. ID Menu 68
- 5.5.2 Using a Stored ID 69
- 5.5.4 Clearing ID Codes 70
- 5.6 WeighVault 71
- 5.6.2 Using WeighVault 72
- 5.7 Totalization Counts 73
- 5.8 Parts Reduction Counts 74
- 5.10 Batch Operations 75
- DIGITAL I/O 76
- 5.12 USB Keyboard 77
- 6.0 Serial Commands 78
- 6.1.2 ID Commands 79
- 6.1.3 Reporting Commands 79
- 6.1.6 Normal Mode Commands 84
- 6.1.7 Unique Commands 84
- 7.0 Print Formatting 85
- Table 7-3. H1, H2 Formats 88
- 7.2 Customizing Print Formats 89
- 7.2.3 Using Revolution 90
- 7.2.4 Print Label Examples 90
- Count Format 91
- Pallet Label Format 91
- Gross Label Format 91
- Setpoint Format 92
- Total Label Format 92
- Gross/Tare/Net Label Format 93
- Accum Label Format 93
- 8.1 Enclosure Disassembly 94
- 8.2 WLAN Card Installation 94
- - - - - - 95
- 9.2.1 Using the P EDP Command 96
- <LF> 97
- 9.6 Digital Filtering 100
- 9.6.4 Audit Trail Support 101
- 9.7 USB Keyboard Interface 102
- 9.8 Serial Scale Interface 102
- 9.9 Regulatory Mode Functions 103
- 9.11 Updating Firmware 105
- Figure 9-4. Revolution Screen 106
- 9.12 Specifications 107
- 9.13 Specifications 108
- Counterpart Limited Warranty 109
- For More Information 110
Related products and manuals for Scales Rice-lake Counterpart Configurable Counting Indicator - Inst
Scales Rice-lake CW-90X Base User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 2.389 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals