Rice-lake Counterpart Configurable Counting Indicator - Inst User Manual Page 41
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Configuration 35
Parameter Choices Description
COUNT NEGCOUNT
SAMPLEQTY
INSFSMPL
LOTUPDT
SCLCHG
NEWITEM
XFRSampl
DISPACC
UNITWTUPDATE
UTWTBASE
DSP Mode
RemovESP
Selects the counting mode (enables/disables negative checkweighing; turns data parameters on/
off. See Figure 3-12.
TARE RND Exact Round When transferring tare to the second scale, tare value remains the exact weight or rounds to
scale resolution.
REGION REGULA
REGWRD
DECFMT
TIME
DATE
Selects regional settings. See Figure 3-13.
UID 1 Sets the unit ID, a string of up to 6 ASCII characters, which can be set via serial port or keypad.
This will be used in place of the <UID> token in a print format. The default value is 1.
SINGLE ID Yes
No
Allows entry of ID to not be stored. Next ID clears field and establishes new data.
CONSC# CURVAL
RESVAL
Allows sequential numbering for print operations.
• CURVAL is the current/starting value
• RESVAL is the ending/reset value
The consecutive number value is incremented following each print operation that includes <CN>
in the ticket format. When the consecutive number is reset, it is reset to the RESVAL specified on
the parameter.
PASSWD CALIBR
SETUP
TEST
T&D
ID
Creates a password to access the CALIBR, SETUP, TEST, T&D, and ID menus. Specify a
non-zero value to restrict access to all configuration menus. Passwords can be overridden by
loading new firmware or entering 999999.
Overriding passwords will clear configuration and calibration settings. To
preserve settings (such as ID information), use Revolution software to upload
your data to a PC, and then download it back to the indicator after the
password override is performed.
SOFTKEYS SK1-12 See Figure 3-14.
KEYLCK MENU
ZERO
GRSNET
UNITS
PRINT
TARE
NUMBER
SAMPLE
UNIT WT
Disables the MENU, ZERO, GROSS/NET, UNITS, PRINT, TARE numeric, SAMPLE and UNIT
WEIGHT keys. Select LOCK to disable the key, and UNLOCK to enable the key.
STNDBY 0 Standby mode delay. Specifies the number of minutes the indicator must be inactive before
entering standby mode. Valid values are 0 (off) through 255 minutes. When in standby mode,
power is still supplied to the CPU and draws half of the current as when the display is powered.
The display is no longer updated and the backlight is off. Press any key to exit standby mode and
reactivate the display.The indicator enters standby mode if no key presses, serial
communications, or scale motion occur for the length of time specified in this parameter. Set to 0
to disable standby mode.
If regulatory agency is set for NONE or INDUST, the standby will occur after
the specified number of minutes regardless of how much weight is on any of
the scales. If regulatory agency is set for NTEP, OIML, or Canada a standby
will only occur when the weight on the currently viewed scale is at center of zero.
Table 3-10. Feature Menu Parameters
Note
Note
- Counterpart 1
- User Manual 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 8
- 1.4 Keypad Functions 9
- 1.5 Tare Recall 10
- 1.6 Annunciator Symbols 10
- 1.7 Softkey Setup 11
- 1.9 Indicator Operations 11
- 2.0 Installation 13
- Important 13
- 2.3 Enclosure Disassembly 15
- 2.5 Making Power Connections 16
- 2.6 Load Cell Wiring 16
- 2.7 Wire Specifics 17
- 2.8 Cable Grounding 18
- 2.9 Enclosure Reassembly 19
- 2.10 CPU Board Removal 19
- 2.13 Installing Option Cards 21
- Figure 2-14. CPU Board 22
- Counterpart Front View 25
- Counterpart Dimensions 27
- 3.0 Configuration 28
- 3.3 Revolution Configuration 29
- 3.4 ID Menu 30
- 3.5 Audit Menu 31
- 3.6 Calibration Menu 32
- 3.7 Setup Menu 33
- 3.7.1 Scale Menu 34
- Scale Calibration Menu 37
- Scale Format Menu 38
- Scale Format Menu Parameters 39
- 3.7.2 Feature Menu 40
- UNITWTUPDATE 41
- Feature Count Menu 42
- Feature Region Menu 44
- SOFTKEYS Menu 45
- Regulate Industry Menu 46
- 3.7.3 Serial Menu 48
- 3.7.4 Ethernet Menu 50
- 3.7.5 Print Format Menu 51
- 3.7.6 Scale Setpoints Menu 52
- LIST OF 53
- 3.7.7 DIG I/O Menu 56
- 3.8 Test Menu 57
- 3.9 Display Menu 58
- SETPT 2 - 6 59
- 4.0 Calibration 61
- 4.2 Five-point Linearization 62
- 4.3 Rezero 62
- 4.4 EDP Command Calibration 62
- 4.5 Revolution 63
- Calibration 63
- 4.6 More About Calibration 64
- 5.0 Scale Operations 65
- 0.000653642 - 0.000653 x 100 66
- 0.000653642 66
- = 0.098% 66
- Figure 5-1. ID Menu 68
- 5.5.2 Using a Stored ID 69
- 5.5.4 Clearing ID Codes 70
- 5.6 WeighVault 71
- 5.6.2 Using WeighVault 72
- 5.7 Totalization Counts 73
- 5.8 Parts Reduction Counts 74
- 5.10 Batch Operations 75
- DIGITAL I/O 76
- 5.12 USB Keyboard 77
- 6.0 Serial Commands 78
- 6.1.2 ID Commands 79
- 6.1.3 Reporting Commands 79
- 6.1.6 Normal Mode Commands 84
- 6.1.7 Unique Commands 84
- 7.0 Print Formatting 85
- Table 7-3. H1, H2 Formats 88
- 7.2 Customizing Print Formats 89
- 7.2.3 Using Revolution 90
- 7.2.4 Print Label Examples 90
- Count Format 91
- Pallet Label Format 91
- Gross Label Format 91
- Setpoint Format 92
- Total Label Format 92
- Gross/Tare/Net Label Format 93
- Accum Label Format 93
- 8.1 Enclosure Disassembly 94
- 8.2 WLAN Card Installation 94
- - - - - - 95
- 9.2.1 Using the P EDP Command 96
- <LF> 97
- 9.6 Digital Filtering 100
- 9.6.4 Audit Trail Support 101
- 9.7 USB Keyboard Interface 102
- 9.8 Serial Scale Interface 102
- 9.9 Regulatory Mode Functions 103
- 9.11 Updating Firmware 105
- Figure 9-4. Revolution Screen 106
- 9.12 Specifications 107
- 9.13 Specifications 108
- Counterpart Limited Warranty 109
- For More Information 110
Related products and manuals for Scales Rice-lake Counterpart Configurable Counting Indicator - Inst
Scales Rice-lake CW-90X Base User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 1.803 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals