Rice-lake Counterpart Configurable Counting Indicator - Inst User Manual Page 11
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Introduction 5
1.7 Softkey Setup
Softkeys offer additional ways to access features associated with the Counterpart. To access the softkey setup
parameter, go to
Menu/Setup/Config/Feature/Softkeys.
Select information for each softkey and press TARE (Enter) key after each entry and then press SaveExit softkey. To
exit back out of the unit, press the
MENU SETUP key twice without saving changes.
Softkeys set for either Display Tare or Display Accum will automatically time out and revert to the normal
active display after 10 seconds.
1.8 How to Use AlphaNumeric Keypad
Counterpart has the ability to use alpha characters along with numeric characters. Use the following steps to
change to alpha characters:
1. Select a key labeled with the value desired.
2. Push until the desired value appears, e.g. 2 abcABC.
3. Move to the next letter and push until that value appears.
4. If the next letter is the same key, push the right arrow (PRINT) to move over to the next selection.
5. When complete, push TARE( Enter) to save.
1.9 Indicator Operations
Basic Counterpart operations are summarized below.
Toggle Gross/Net
Press the GROSS/NET key to switch the display mode from gross to net or from net to gross. If a tare value has been
entered or acquired, the net value is the gross weight minus the tare. If no tare has been entered or acquired, the
display remains in gross mode.
Gross mode and net mode is indicated by the annunciator on the display.
Toggle Units
Press the UNITS TOGGLE key to switch between primary, secondary, and tertiary units.
Zero Scale
1. While in gross mode, remove all weight from the scale and wait for the standstill annunciator ( ).
2. Press the ZERO key. The zero annunicator is displayed to indicate the scale is zeroed.
Acquire Tare
1. Place a container on the scale and wait for the standstill annunicator ( ).
2. Press the TARE key to acquire the tare weight of the container.
3. The Net annunciator will be enabled.
Remove Stored Tare Value
1. Remove all weight from the scale and wait for the standstill annunciator ( ).
2. Press the TARE key. The display shifts to gross weight and the Gross annunciator is displayed.
Keyed Tare
1. Key in the value of the container.
2. Press the TARE key.
3. The Net annunciator is displayed.
Print
Press the PRINT key to print either the Gross, Net, Total or Count format.
The default format is a 2.25 x 4.5 inch label.
1. Wait for standstill annunciator ( ).
2. Press PRINT key to send data to the serial port.
If the standstill annunciator is not present, the PRINT key command is executed if the scale comes out of motion
within three seconds.
Note
- Counterpart 1
- User Manual 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 8
- 1.4 Keypad Functions 9
- 1.5 Tare Recall 10
- 1.6 Annunciator Symbols 10
- 1.7 Softkey Setup 11
- 1.9 Indicator Operations 11
- 2.0 Installation 13
- Important 13
- 2.3 Enclosure Disassembly 15
- 2.5 Making Power Connections 16
- 2.6 Load Cell Wiring 16
- 2.7 Wire Specifics 17
- 2.8 Cable Grounding 18
- 2.9 Enclosure Reassembly 19
- 2.10 CPU Board Removal 19
- 2.13 Installing Option Cards 21
- Figure 2-14. CPU Board 22
- Counterpart Front View 25
- Counterpart Dimensions 27
- 3.0 Configuration 28
- 3.3 Revolution Configuration 29
- 3.4 ID Menu 30
- 3.5 Audit Menu 31
- 3.6 Calibration Menu 32
- 3.7 Setup Menu 33
- 3.7.1 Scale Menu 34
- Scale Calibration Menu 37
- Scale Format Menu 38
- Scale Format Menu Parameters 39
- 3.7.2 Feature Menu 40
- UNITWTUPDATE 41
- Feature Count Menu 42
- Feature Region Menu 44
- SOFTKEYS Menu 45
- Regulate Industry Menu 46
- 3.7.3 Serial Menu 48
- 3.7.4 Ethernet Menu 50
- 3.7.5 Print Format Menu 51
- 3.7.6 Scale Setpoints Menu 52
- LIST OF 53
- 3.7.7 DIG I/O Menu 56
- 3.8 Test Menu 57
- 3.9 Display Menu 58
- SETPT 2 - 6 59
- 4.0 Calibration 61
- 4.2 Five-point Linearization 62
- 4.3 Rezero 62
- 4.4 EDP Command Calibration 62
- 4.5 Revolution 63
- Calibration 63
- 4.6 More About Calibration 64
- 5.0 Scale Operations 65
- 0.000653642 - 0.000653 x 100 66
- 0.000653642 66
- = 0.098% 66
- Figure 5-1. ID Menu 68
- 5.5.2 Using a Stored ID 69
- 5.5.4 Clearing ID Codes 70
- 5.6 WeighVault 71
- 5.6.2 Using WeighVault 72
- 5.7 Totalization Counts 73
- 5.8 Parts Reduction Counts 74
- 5.10 Batch Operations 75
- DIGITAL I/O 76
- 5.12 USB Keyboard 77
- 6.0 Serial Commands 78
- 6.1.2 ID Commands 79
- 6.1.3 Reporting Commands 79
- 6.1.6 Normal Mode Commands 84
- 6.1.7 Unique Commands 84
- 7.0 Print Formatting 85
- Table 7-3. H1, H2 Formats 88
- 7.2 Customizing Print Formats 89
- 7.2.3 Using Revolution 90
- 7.2.4 Print Label Examples 90
- Count Format 91
- Pallet Label Format 91
- Gross Label Format 91
- Setpoint Format 92
- Total Label Format 92
- Gross/Tare/Net Label Format 93
- Accum Label Format 93
- 8.1 Enclosure Disassembly 94
- 8.2 WLAN Card Installation 94
- - - - - - 95
- 9.2.1 Using the P EDP Command 96
- <LF> 97
- 9.6 Digital Filtering 100
- 9.6.4 Audit Trail Support 101
- 9.7 USB Keyboard Interface 102
- 9.8 Serial Scale Interface 102
- 9.9 Regulatory Mode Functions 103
- 9.11 Updating Firmware 105
- Figure 9-4. Revolution Screen 106
- 9.12 Specifications 107
- 9.13 Specifications 108
- Counterpart Limited Warranty 109
- For More Information 110
Related products and manuals for Scales Rice-lake Counterpart Configurable Counting Indicator - Inst
Scales Rice-lake CW-90X Base User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.208 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals