Rice-lake Counterpart Configurable Counting Indicator - Inst User Manual Page 73
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Scale Operations 67
5.7 Totalization Counts
Counterpart
has a totalization function that allows you to totalize the quantity of several weighings together. This is
especially helpful if putting together parts kits. The ID code is functional with totalization, count or weight.
For full operation of the totalization feature, configure the unit with the following softkeys:
TOTAL+
TOTAL-
Clear Total
To find the total accumulated quantity of similar containers filled with parts, use the totalization procedure detailed
below. Six containers are used in this example; all containers are of the same empty weight.
1. Conduct a sampling process to determine the unit weight of the pieces, or key in a known unit weight or
recall an ID.
2. Enter a known tare weight or place an empty container on the scale to perform tare function. If an ID was
recalled in step 1, its tare value is already loaded.
3. Place container 1 (full of parts) on the scale. The number of pieces in the container is shown in the PCS
area of the display.
4. Press the Total + softkey to store the number of pieces in container 1. The memory (M) icon is shown. The
net weight of the items in the containers is stored and the totalization count is incremented. The piece count
value is displayed. The total count is shown in place of the unit weight display, and it is labeled as Total
Weight
ttl.
5. Remove container 1 and place container 2 (full of parts) on the scale.
6. Press the Total + softkey. The accumulated total is now equal to container 1 plus container 2. The displayed
total is also updated.
7. Continue with the remainder of the containers in the same totalization method. The total number of parts
stored in all six containers (and the weight of the parts in those containers) is now stored and shown on the
display.
• An ID may be loaded while part totalization is being performed, the ID Quantity value is not affected by
the totalizations operations.
• If a totalization has been started and the Code softkey is pressed — the unit will prompt Exit Totalization
Mode? with Yes and No softkeys. Pressing Yes clears the total, exits from totalization mode and brings up
the normal prompt for entering an ID code. If No is pressed, the unit does not prompt for an ID Code and
totalization can continue.
• The user cannot switch to another scale during totalization. If the Unit Toggle key is pressed during
totalization, the message not allowed — totalizing will be displayed and the switch will not occur.
• The user cannot switch units during totalization. If the Unit Toggle key is pressed during totalization, the
message
not allowed - totalizing will be displayed and the switch will not occur.
• During totalization an icon is displayed between the battery icon and the main display area label. The icon
is an uppercase M for memory.
• For each totalization done (Total+ or Total-) a count will be incremented. This value can be printed. When
the total value is cleared and totalization mode is exited, the count will be cleared as well.
• While in totalization mode, pressing the Print key will print the total format — TOTALFMT.
• When attempting a totalization, a motion check can be performed based upon the setting of the TOTAL
parameter in the Feature/Count menu. If Total is ON and if there is motion, then one more attempt will be
made after two seconds. The default setting is OFF.
• To clear the total value, press the Clear Total softkey, and it will clear the total value.
Note
- Counterpart 1
- User Manual 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 8
- 1.4 Keypad Functions 9
- 1.5 Tare Recall 10
- 1.6 Annunciator Symbols 10
- 1.7 Softkey Setup 11
- 1.9 Indicator Operations 11
- 2.0 Installation 13
- Important 13
- 2.3 Enclosure Disassembly 15
- 2.5 Making Power Connections 16
- 2.6 Load Cell Wiring 16
- 2.7 Wire Specifics 17
- 2.8 Cable Grounding 18
- 2.9 Enclosure Reassembly 19
- 2.10 CPU Board Removal 19
- 2.13 Installing Option Cards 21
- Figure 2-14. CPU Board 22
- Counterpart Front View 25
- Counterpart Dimensions 27
- 3.0 Configuration 28
- 3.3 Revolution Configuration 29
- 3.4 ID Menu 30
- 3.5 Audit Menu 31
- 3.6 Calibration Menu 32
- 3.7 Setup Menu 33
- 3.7.1 Scale Menu 34
- Scale Calibration Menu 37
- Scale Format Menu 38
- Scale Format Menu Parameters 39
- 3.7.2 Feature Menu 40
- UNITWTUPDATE 41
- Feature Count Menu 42
- Feature Region Menu 44
- SOFTKEYS Menu 45
- Regulate Industry Menu 46
- 3.7.3 Serial Menu 48
- 3.7.4 Ethernet Menu 50
- 3.7.5 Print Format Menu 51
- 3.7.6 Scale Setpoints Menu 52
- LIST OF 53
- 3.7.7 DIG I/O Menu 56
- 3.8 Test Menu 57
- 3.9 Display Menu 58
- SETPT 2 - 6 59
- 4.0 Calibration 61
- 4.2 Five-point Linearization 62
- 4.3 Rezero 62
- 4.4 EDP Command Calibration 62
- 4.5 Revolution 63
- Calibration 63
- 4.6 More About Calibration 64
- 5.0 Scale Operations 65
- 0.000653642 - 0.000653 x 100 66
- 0.000653642 66
- = 0.098% 66
- Figure 5-1. ID Menu 68
- 5.5.2 Using a Stored ID 69
- 5.5.4 Clearing ID Codes 70
- 5.6 WeighVault 71
- 5.6.2 Using WeighVault 72
- 5.7 Totalization Counts 73
- 5.8 Parts Reduction Counts 74
- 5.10 Batch Operations 75
- DIGITAL I/O 76
- 5.12 USB Keyboard 77
- 6.0 Serial Commands 78
- 6.1.2 ID Commands 79
- 6.1.3 Reporting Commands 79
- 6.1.6 Normal Mode Commands 84
- 6.1.7 Unique Commands 84
- 7.0 Print Formatting 85
- Table 7-3. H1, H2 Formats 88
- 7.2 Customizing Print Formats 89
- 7.2.3 Using Revolution 90
- 7.2.4 Print Label Examples 90
- Count Format 91
- Pallet Label Format 91
- Gross Label Format 91
- Setpoint Format 92
- Total Label Format 92
- Gross/Tare/Net Label Format 93
- Accum Label Format 93
- 8.1 Enclosure Disassembly 94
- 8.2 WLAN Card Installation 94
- - - - - - 95
- 9.2.1 Using the P EDP Command 96
- <LF> 97
- 9.6 Digital Filtering 100
- 9.6.4 Audit Trail Support 101
- 9.7 USB Keyboard Interface 102
- 9.8 Serial Scale Interface 102
- 9.9 Regulatory Mode Functions 103
- 9.11 Updating Firmware 105
- Figure 9-4. Revolution Screen 106
- 9.12 Specifications 107
- 9.13 Specifications 108
- Counterpart Limited Warranty 109
- For More Information 110
Related products and manuals for Scales Rice-lake Counterpart Configurable Counting Indicator - Inst
Scales Rice-lake CW-90X Base User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.711 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals